|
Home Page > Executive Branch > Code of Federal Regulations > Electronic Code of Federal Regulations
e-CFR Data is current as of February 4, 2010
TITLE 49--Transportation
Subtitle B--OTHER REGULATIONS RELATING TO TRANSPORTATION
CHAPTER I--PIPELINE AND HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION
SUBCHAPTER D--PIPELINE SAFETY
PART 195--TRANSPORTATION OF HAZARDOUS LIQUIDS BY PIPELINE
Subpart A--GENERAL
|
| Which pipelines are covered by this part? |
|
|
| Incorporation by reference. |
|
|
| Compatibility necessary for transportation of hazardous liquids or carbon dioxide. |
|
|
| Conversion to service subject to this part. |
|
|
| Unusually Sensitive Areas (USAs). |
|
|
| Transportation of hazardous liquid or carbon dioxide in pipelines constructed with other than steel pipe. |
|
|
| Outer continental shelf pipelines. |
|
|
| Responsibility of operator for compliance with this part. |
|
|
| What is a regulated rural gathering line and what requirements apply? |
|
|
| What requirements apply to low-stress pipelines in rural areas? |
|
Subpart B--ANNUAL, ACCIDENT, AND SAFETY-RELATED CONDITION REPORTING
|
| Telephonic notice of certain accidents. |
|
|
| Reporting safety-related conditions. |
|
|
| Filing safety-related condition reports. |
|
|
| Filing offshore pipeline condition reports. |
|
|
| Address for written reports. |
|
|
| Abandonment or deactivation of facilities. |
|
|
| Operator assistance in investigation. |
|
|
| Supplies of accident report DOT Form 7000-1. |
|
|
| OMB control number assigned to information collection. |
|
Subpart C--DESIGN REQUIREMENTS
|
| Qualifying metallic components other than pipe. |
|
|
| Internal design pressure. |
|
|
| Passage of internal inspection devices. |
|
|
| Fabricated branch connections. |
|
|
| Design and construction of aboveground breakout tanks. |
|
Subpart D--CONSTRUCTION
|
| Compliance with specifications or standards. |
|
|
| Repair, alteration and reconstruction of aboveground breakout tanks that have been in service. |
|
|
| Welding of supports and braces. |
|
|
| Welders: Qualification of welders. |
|
|
| Welds and welding inspection: Standards of acceptability. |
|
|
| Welds: Repair or removal of defects. |
|
|
| Welds: Nondestructive testing. |
|
|
| Installation of pipe in a ditch. |
|
|
| Cover over buried pipeline. |
|
|
| Clearance between pipe and underground structures. |
|
|
| Crossing of railroads and highways. |
|
|
| Impoundment, protection against entry, normal/emergency venting or pressure/vacuum relief for aboveground breakout tanks. |
|
Subpart E--PRESSURE TESTING
|
| Risk-based alternative to pressure testing older hazardous liquid and carbon dioxide pipelines. |
|
|
| Pressure testing aboveground breakout tanks. |
|
Subpart F--OPERATION AND MAINTENANCE
|
| Procedural manual for operations, maintenance, and emergencies. |
|
|
| Emergency response training. |
|
|
| Protection against ignitions and safe access/egress involving floating roofs. |
|
|
| Maximum operating pressure. |
|
|
| Inspection of rights-of-way and crossings under navigable waters. |
|
|
| Underwater inspection and reburial of pipelines in the Gulf of Mexico and its inlets. |
|
|
| Scraper and sphere facilities. |
|
|
| Overpressure safety devices and overfill protection systems. |
|
|
| Inspection of in-service breakout tanks. |
|
|
| Damage prevention program. |
|
|
| Pipeline integrity management in high consequence areas. |
|
Subpart G--QUALIFICATION OF PIPELINE PERSONNEL
Subpart H--CORROSION CONTROL
|
| What do the regulations in this subpart cover? |
|
|
| What special definitions apply to this subpart? |
|
|
| What are the qualifications for supervisors? |
|
|
| Which pipelines must have coating for external corrosion control? |
|
|
| What coating material may I use for external corrosion control? |
|
|
| When must I inspect pipe coating used for external corrosion control? |
|
|
| Which pipelines must have cathodic protection? |
|
|
| How do I install cathodic protection on breakout tanks? |
|
|
| Which pipelines must have test leads and what must I do to install and maintain the leads? |
|
|
| Do I have to examine exposed portions of buried pipelines? |
|
|
| What criteria must I use to determine the adequacy of cathodic protection? |
|
|
| What must I do to monitor external corrosion control? |
|
|
| Which facilities must I electrically isolate and what inspections, tests, and safeguards are required? |
|
|
| What must I do to alleviate interference currents? |
|
|
| What must I do to mitigate internal corrosion? |
|
|
| Which pipelines must I protect against atmospheric corrosion and what coating material may I use? |
|
|
| What must I do to monitor atmospheric corrosion control? |
|
|
| What must I do to correct corroded pipe? |
|
|
| What methods are available to determine the strength of corroded pipe? |
|
|
| What standards apply to direct assessment? |
|
|
| What corrosion control information do I have to maintain? |
|
|
| Appendix A to Part 195
--Delineation Between Federal and State Jurisdiction--Statement of Agency Policy and Interpretation |
|
|
| Appendix B to Part 195
--Risk-Based Alternative to Pressure Testing Older Hazardous Liquid and Carbon Dioxide Pipelines |
|
|
